Implementing Budapest we did USART using PIC16F877A + MPLAB X

Implementing Budapest we did USART using PIC16F877A + MPLAB X - It’s also fully customisable (unlike the Bixby button on the left edge of the phone) so you can use it how you like. Developers will also be able to make use of this in apps. The S Pen only takes 40 seconds to charge once slotted into the phone and lasts for 30 minutes. You can still use the old direct-to-screen functions when it's dead, though. On holiday in Budapest, well we have collected a lot of data from the field directly and from many other blogs so very complete his discussion here about Implementing Budapest we did USART using PIC16F877A + MPLAB X, on this blog we also have to provide the latest automotive information from all the brands associated with the automobile. ok please continue reading:

The Universal Synchronous Asynchronous Receiver Transmitter (USART) module is one of the two serial I/O modules in PIC16F877A. (USART is also known as a Serial Communications Interface or SCI.) The USART can be configured as a full duplex asynchronous system that can communicate with peripheral devices such as CRT terminals and personal computers, or it can be configured as a half duplex synchronous system that can communicate with peripheral devices such as A/D or D/A integrated circuits, serial EEPROMs etc.

5 Registers are used for USART in PIC16F877A and they are 

• TXSTA - Transmit status and control Register
• RCSTA - Receiver status and control Register
• TXREG -USART Transmit Data Register 
• RCREG - USART Receive Data Register
• SPBRG - Baud Rate Generator Register
  

Steps to follow when setting up an Asynchronous Transmission
1.Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired,

set bit BRGH .

2. Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN.

3. If interrupts are desired, then set enable bit RCIE.

4. If 9-bit reception is desired, then set bit RX9.

5. Enable the reception by setting bit CREN.

6.Flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE is set.

7. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception.

8. Read the 8-bit received data by reading the RCREG register.

9. If any error occurred, clear the error by clearing enable bit CREN.

10. If using interrupts, ensure that GIE and PEIE (bits 7 and 6) of the INTCON register are set.

To start programming in MPLAB X follow the steps as in the :  Blinking a LED using MPLAB X , PIC16F877A

up to 9th step same as in  Blinking a LED using MPLAB X , PIC16F877A

The main program have a change according to the steps for Asynchronous Transmission

#########################################################################

/* Asynchronous Transmission in  PIC16F877A

 * File:   main.c

 * Author: ebin

 *

 * Created on 10 September, 2012, 11:39 AM

 */

#include <htc.h>

#if defined(WDTE_OFF)

__CONFIG(WDTE_OFF & LVP_OFF);

#elif defined (WDTDIS)

__CONFIG(WDTDIS & LVPDIS);

#endif

int main(void)

{

    TRISC6 = 0;

    TRISC7 = 1;

    SPBRG = 25 ;

    BRGH =1 ;

    SPEN =1 ;

    SYNC = 0 ;

    CREN =1 ;

    TXEN =1;

    

    while (1)

    {

        TXREG ='A';

        while(TXIF == 0);

        TXIF=0;

    }

 return 0;

}

##############################################################################

Tecno N8 Price, Specifications & Features
https://ikkemunandar.blogspot.com/2016/09/tecno-n8-price-specifications-features.html
Infinity Box Chinese Miracle 2 MTK v 1.58 setup download
https://ikkemunandar.blogspot.com/2016/10/infinity-box-chinese-miracle-2-mtk-v.html
Z3X BOX Samsung Tool PRO V 26.9 Setup Download
https://ikkemunandar.blogspot.com/2016/10/z3x-box-samsung-tool-pro-v-269-setup.html